INSTALLATION

Step 1.
Please remove any protective film or covers before cooler installation .

 

Step 2.
If the heat sink base of the cooler does not contain any thermal interface material (picture A)

Please take the cooler and apply a small amount of the thermal paste provided to the center of the base of the heat-sink. (Picture B)

A B

 

 

 

Step 3.

Gently put the cooler on the CPU, Latch tail of clip to protruding ear on the side of the ZIF socket.

 

 

Step 4.
If the clip provided on this cooler does not have a tap to push down (picture A) Please i nsert a 4mm flat bladed screwdriver into the pocket of the clip and than push down and leaver back so it clips over protruding ear on the opposite side of ZIF socket. (Picture B)

AB

 

 

Step 5.
Connect the fan connector onto the motherboard fan header.

Assembly finished.

Step 1.
Please remove protective film before cooler installation.

Step 2.
Put the supporting (black) clip on the mainboard and push down until it locks.

Step 3.
Put the cooler on the CPU, latch tail of the metal clip to protruding ear on the side of the supporting clip. Then push down and leaver back so it clips over protruding ear on the opposite side of the supporting clip.

Step 4.
Connect the 3pin fan connector onto the motherboard 3pin fan header. Assembly finished.

Step 1.
Please remove any protective film or covers before cooler installation .

 

Step 2.
If the heat sink base of the cooler does not contain any thermal interface material (picture A)

Please take the cooler and apply a small amount of the thermal paste provided to the center of the base of the heat-sink. (Picture B)

A B

 

 

 

Step 3.

Gently put the cooler on the CPU, Latch tail of clip to protruding ear on the side of the ZIF socket.

 

 

Step 4.
If the clip provided on this cooler does not have a tap to push down (picture A) Please i nsert a 4mm flat bladed screwdriver into the pocket of the clip and than push down and leaver back so it clips over protruding ear on the opposite side of ZIF socket. (Picture B)

AB

 

 

Step 5.
Connect the fan connector onto the motherboard fan header.

Assembly finished.

Step 1.
Please remove protective plastic before cooler installation.

Step 2.
Put the supporting (black) clip on the mainboard and push down until it locks.

Step 3.
Fit the leavered clip and then push down and leaver back so it clips over protruding ear on the opposite side of the supporter.

Step 4.
Connect the 3pin fan connector onto the motherboard 3pin fan header.

Assembly finished.

Step 1.
Please remove protective cover before cooler installation.

Step 2.
Put the cooler on the CPU.

Step 3.
Put one hand on the cooler to hold it, then push down the railing of the clip, so it clips into the holes of the supporter on the mainboard.

Step 4.
Connect the 3pin fan connector onto the motherboard 3pin fan header.

Assembly finished.

Step 1.
Take the cooler and apply a small amount of the thermal paste provided to the center of the base of the heat-sink.

Step 2.

Fit the supplied supporter bracket to the upside of the motherboard. Insert the supplied screws to each post. Do not tighten them fully until all have been tightened equally cross ways.

Step 3.
Gently place the cooler over the supporter bracket and attach the end with the screw driver slot to the plastic frame. This is the end opposite to the locking leaver.

Step 4.
At the lever end of the fan assembly push the clip down until it locks over the plastic frame. Rotate the leaver until it locks into place.

Step 5.
Connect the fan connector onto the motherboard fan header.

Assembly finished.

Step 1.
Please remove any protective film or covers before cooler installation.

Step 2.
Take the cooler and apply a small amount of the thermal paste provided to the center of the base of the heat-sink.

Step 3.
Once the CPU has been fitted gently place the cooler onto the motherboard ensuring that the fixing push-pins align with the 4 openings on the motherboard.

Step 4.
Fit each of the clips to each opening. Once the cooler has been fitted onto the motherboard, push down the black clips and turn clockwise to secure the cooler.

AB

 Step 5.
Connect the fan connector onto the motherboard fan header.

Assembly finished.